International Options
Destination
United Kingdom
Currency
GBP £  GBP

United Kingdom
Shopping Basket
Your basket is empty
Cleghorn - About Sea Water Pumps

Seawater is corrosive.  Bronze (an alloy based on copper and tin) has been used for centuries for its corrosion resistance in harsh marine environments.  Cast iron and steel pumps start to rust and rot as soon as they enter seawater service.  Bronze pumps will last for years, giving reliable performance when it is most needed. 

As seawater pumping specialists for over 40 years, our stocked range of bronze seawater pumps is large and our applications knowledge is extensive.  We can specify and supply pumps for engine cooling, bilge, deckwash, fire, and many other saltwater applications.  We stock bare-shaft bronze pumps for engine drive, and DC and AC electric motor-pump units.  Technical advice is always available.

-  bare-shaft pedestal-mounted pumps, for direct or belt drive
-  mechanical or electro-magnetic clutch-pump units
-  AC and DC electric motor-pump units.

JABSCO bronze flexible impeller pumps
52040.jpg (3111 bytes) Our speciality - we hold just about the largest stock of JABSCO bronze flexible impeller pumps and spare parts to be found anywhere. 
Port sizes up to 65mm (2.5"), flow rates up to 500 litres/minute (110 gallons/minute), pressures up to 2.5bar.  
You can find and buy Jabsco pumps and spares at www.JABSCOshop.co.uk
FP-series bronze pumps
AM40 Bare Shaft Pump FP bronze self-priming centrifugal pumps.  Engine-driven, AC and DC electric units. 
Port sizes 38-65mm (1.5 - 2.5"), flow rates up to 80 m³/hour, heads up to 50m, absorbed power up to 45kW .
CM125 Bare Shaft Pump FP bronze end-suction centrifugal pumps.  Non-self-priming engine-driven, AC and DC electric units. 
Port sizes 38-125mm (1.5 - 5"), flow rates up to 500 m³/hour, heads up to 60m, absorbed power up to 100kW
TS Pump FP bronze self-priming regenerative pumps develop high heads at comparatively low rotational speeds (from 1200rpm). 
Engine-driven, AC and DC electric units.  Port sizes 38-65mm (1.5 to 2.5"), flow rates up to 30 m³/hour, heads up to 70m.
GR-series bronze pumps
CP DC Pump

GR-series DC electric self-priming regenerative pumps
Port sizes 20-38mm, flow rates from 2l/min to 250l/min, heads up to 33m

GR-series AC electric self-priming regenerative pumps
Port sizes 32-50mm, flow rates from 2l/min to 400l/min, heads up to 24m

 

Jet Pump

GR-series AC and DC electric jet pumps
Very quiet running self-priming pumps in bronze, designed for use in pressurised fresh- or salt-water systems.  See also Marine Pressurised Water Systems
Port sizes 28-38mm, flow rates from 20l/min to 160l/min, pressures up to 5bar

ACM Bareshaft Pump

GR-series horizontal multistage regenerative pumps
Bare-shaft bronze pumps for long-coupled electric motor drive
Port sizes 20-65mm, flow rates from 0.3m³/hr to 36m³/hr, heads up to 230m

ACM Motor Pump Unit

GR-series close-coupled electric regenerative motor-pump units
Port sizes 32-50mm, flow rates from 1m³/hr to 24m³/hr, heads up to 80m

Oberdorfer bronze pumps
OB Gear Pump Oberdorfer gear pumps
Low flow rates at high pressures.  Oberdorfer gear pumps can handle seawater as well as free-flowing oils
Port sizes 6-25mm, flow rates from 4l/min to 800l/min, pressures up to 10bar
OB Self-priming Centrifugal Pump


Oberdorfer self-priming horizontal centrifugal pump
Port size 25mm, flow rates up to 90l/min, heads up to 10m

OB End suction Centrifugal Pump

Oberdorfer non- self-priming horizontal centrifugal pumps
Port sizes 10-25mm, flow rates from 15l/min to 800l/min, heads up to 50m

For more information or a quote mail us now (mail@cleghorn.co.uk).